Skip to search Skip to navigation menu Skip to main content Selecting option will reload page

Category: General Crafts

DIY Decorative Bobby Pins

beaded_bobby_pinsThings you need:
Bobby Pins
Beads
34 gauge Silver Beading Wire
Wire Cutter or Fingernail Clipper

Things to do:
1. Cut a 20″ length of the beading wire and slip through the bend of the bobby pin; pull through until both ends are even and then cross the two ends of the wire where they touch the bobby pin.
2. Thread a bead onto both wires; adjust to make sure the bead is facing up” or positioned neatly, and then cross the wires in front of the bead.
3. Continue with your pattern, threading beads and crossing the wires over until you reach the rubber tip.
4. Finish by wrapping the wire around the bobby pin several times to secure, and then trim the excess.

Tip: The additional wire will make bobby pins fit snugly; for a comfortable fit, choose bobby pins one size larger than what you usually wear.

With handcrafted hair accessories, transforming a hairdo from ho-hum” to ooh-la-la” couldn’t be easier! With a little practice, creativity, and the right stash of supplies on hand, you’ll never have to settle for run-of-the-mill store-bought hair accessories again.

Photo Credit: K. Person

Continue Reading

Recycled Bird Feeder for Hummingbirds

hummingbird_feeder
Using materials already on hand to make hummingbird feeders is a fun and simple craft that serves triple duty. Not only will you be helping the planet and feeding hummingbirds, you’ll also receive hours of enjoyment by watching these winged jewels flit throughout your garden or flowerbeds.

Things you need:
Wide-mouth plastic bottle with cap (Gatorade bottles work great)
A bottle cap that is slightly larger and deeper than the Gatorade bottle cap
Drill
Pliers
Paper towel
Hot glue gun with glue sticks
Red non-toxic, low VOC paint
Sandpaper
Faux flowers (or, make your own from recycled aluminum foil or foil pie pans)
20-40″ piece of 20 gauge wire

Things to do:
1. To begin, drill several small holes in a cluster through the center of the Gatorade cap, then use pliers to punch out the holes completely to form one large hole. Stuff the hole with the tip of a paper towel to form a spacer, and place the Gatorade cap inside the larger cap.
2. Next, use the hot glue gun to SLOWLY build up four plus sign” bridges that will hold the lids in place. Tip: During this stage, be sure to leave space between the lids to allow nectar to flow from the bottle into the larger lid and to prevent glue from coating the bottom of the larger lid; otherwise, you’ll fill the cavities that are needed to hold the nectar.
3. To decorate, scuff the surface of the plastic bottle with sandpaper and paint, and use hot glue to affix faux or aluminum foil flowers around the base of the larger lid. (Red dye is harmful to hummingbirds, so if you’re using fabric faux flowers, make sure the dye won’t run or bleed into the nectar.) Finally, use the length of 20 gauge wire to wrap around the bottle, and fashion a hook or loop at the other end for hanging. Now you’re ready to fill, hang, and enjoy the aerial acrobatics!

Homemade Hummer Brew
2 cups water
1/2 cup sugar
Bring water to a boil, stir in sugar until dissolved, and boil the mixture for 2 minutes. Cool completely before filling feeder, and refrigerate any leftovers.

The sky’s the limit when it comes to discovering creative uses for materials already on hand. While recycling is a noble alternative to trashing, upcycling will save even more natural resources. Not only will you avoid purchasing an item to fill a need, but you’ll also save energy that would otherwise be used at the recycling plant. Flex your creative muscles and enjoy making and sharing your eco-friendly crafts.

Continue Reading
Change Your Country
Please select your country, this will change the site to your country's currency:

Cancel